Ce portable ACER ASPIRE 1350 comporte un processeur Mobile AMD Athlon(tm) XP 2600+ à 2,0 GHz, 1 Go de RAM (après mise à jour), un disque de 160 Go (après mise à jour également), une carte vidéo S3 UniChrome, un écran de 15 pouces, un combo DVD/CD-RW, un lecteur de disquettes, une carte réseau, un modem, une carte réseau sans fil, et des ports série, parallèle, Firewire.
Résultat de la commande lspci :
00:00.0 Host bridge: VIA Technologies, Inc. VT8378 [KM400/A] Chipset Host Bridge 00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge 00:07.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 02) 00:08.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link) 00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) 00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) 00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) 00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) 00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge 00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) 00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50) 00:11.6 Communication controller: VIA Technologies, Inc. AC'97 Modem Controller (rev 80) 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74) 01:00.0 VGA compatible controller: VIA Technologies, Inc. VT8378 [S3 UniChrome] Integrated Video (rev 01) 02:00.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)
Le disque a été partitionné de la façon suivante :
Disk /dev/hda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/hda1 * 1 6374 51199123+ 7 HPFS/NTFS /dev/hda2 6375 19300 103828095 83 Linux
Ont été installés dans cet ordre Windows XP Pro sur la partition 1 puis GNU/Linux sur la partition 2 (gestionaire de démarrage Lilo).
La distribution de Linux utilisée est une Slackware 12.0.
La version du noyau (recompilé) est 2.6.23.11.
Les modules
Module Size Used by slamr 433448 2 eeprom 9872 0 i2c_dev 9860 0 ndiswrapper 186780 0 ieee80211softmac 30592 0 ieee80211 35272 1 ieee80211softmac ieee80211_crypt 8704 1 ieee80211 snd_pcm_oss 42656 0 snd_mixer_oss 18048 1 snd_pcm_oss ipv6 261252 14 lp 13220 0 parport_pc 39908 1 parport 36936 2 lp,parport_pc usbhid 22052 0 pcmcia 36780 0 video 21008 0 snd_via82xx 26264 0 backlight 8068 1 video gameport 14984 1 snd_via82xx output 6912 1 video snd_ac97_codec 97440 1 snd_via82xx ac97_bus 6016 1 snd_ac97_codec snd_pcm 72196 3 snd_pcm_oss,snd_via82xx,snd_ac97_codec snd_timer 22532 1 snd_pcm snd_page_alloc 11656 2 snd_via82xx,snd_pcm snd_mpu401_uart 10624 1 snd_via82xx snd_rawmidi 22816 1 snd_mpu401_uart snd_seq_device 10508 1 snd_rawmidi via_agp 12160 1 yenta_socket 27148 2 snd 47076 9 snd_pcm_oss,snd_mixer_oss,snd_via82xx,snd_ac97_c odec,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device ohci1394 32944 0 ieee1394 84024 1 ohci1394 ehci_hcd 33036 0 i2c_viapro 11412 0 uhci_hcd 25996 0 rsrc_nonstatic 14848 1 yenta_socket soundcore 9824 1 snd agpgart 30920 1 via_agp usbcore 120836 5 ndiswrapper,usbhid,ehci_hcd,uhci_hcd i2c_core 23680 3 eeprom,i2c_dev,i2c_viapro via_rhine 24200 0 pcmcia_core 36884 3 pcmcia,yenta_socket,rsrc_nonstatic
$ cat /proc/acpi/battery/BAT1/info present: yes design capacity: 4400 mAh last full capacity: 1600 mAh battery technology: rechargeable design voltage: 14800 mV design capacity warning: 300 mAh design capacity low: 200 mAh capacity granularity 1: 32 mAh capacity granularity 2: 32 mAh model number: ZP02 serial number: 1 battery type: LION OEM info: SIMPLO
$ cat /proc/acpi/thermal_zone/THRM/temperature temperature: 51 C
Il fonctionne avec le pilote http://linmodems.technion.ac.il/packages/smartlink/slmodem-2.9.11-20070813
Après désarchivage, make et make install :
/sbin/modprobe slamr
slmodemd --country=FRANCE /dev/slamr0 &
ln -s /dev/ttySL0 /dev/modem
(sous minicom voir le résultat des commandes ati ati1 ati2 ati3)
slamr: SmartLink AMRMO modem. slamr: probe 1106:3068 VIA3058 card... ACPI: PCI Interrupt 0000:00:11.6[C] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9 PCI: Setting latency timer of device 0000:00:11.6 to 64 slamr: mc97 codec is SIL27 slamr: slamr0 is VIA3058 card.
pilote Via
S'il y a un problème, utiliser xorgconfig et indiquer un autre type de carte (par exemple ATI), puis dans le fichier /etx/X11/xorg.conf modifier les sections « Graphics device section » et « Screen sections » :
Section "Device"
Identifier "via"
Driver "via"
#VideoRam 32768
# Insert Clocks lines here if appropriate
EndSection
Section "Screen"
Identifier "Screen 1"
Device "via"
Monitor "acer"
DefaultDepth 24
...
Pour le reste , du classique :
Section "InputDevice"
# Identifier and driver
Identifier "Mouse1"
Driver "mouse"
Option "Protocol" "IMPS/2"
Option "Device" "/dev/mouse"
Option "ZAxisMapping" "4 5"
Option "Buttons" "5"
HorizSync 48.4
VertRefresh 60
Section "DRI" Mode 0666 EndSection
module snd_via82xx
modules pcmcia yenta_socket
module via_rhine
Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g
ndiswrapper (testé avec version 1.51 installée à partir des sources)
avec pilote Windows XP lsbcmnds (BCM43XG) version 02/14/2005 3.90.36.0
ndiswrapper version 1.51 loaded (smp=yes, preempt=no) ndiswrapper: driver lsbcmnds (The Linksys Group, Inc.,02/14/2005, 3.90.36.0) loaded ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5 ndiswrapper: using IRQ 5 wlan0: ethernet device 00:18:f8:cc:91:09 using NDIS driver: lsbcmnds, version: 0x3644000, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 14E4:4318.5.conf wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK
wlan0 IEEE 802.11g ESSID:off/any Nickname:"azerty"
Mode:Managed Frequency:2.462 GHz Access Point: Not-Associated
Bit Rate=54 Mb/s Tx-Power:25 dBm
RTS thr=2347 B Fragment thr=2346 B
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
# iwlist wlan0 scan
wlan0 Scan completed :
Cell 01 - Address: xx:xx:xx:xx:xx:xx
ESSID:"XXXX"
Protocol:IEEE 802.11g
...
iwconfig eth1 mode managed essid mon-reseau nick ma-machine key restricted 1111-2222-3333-4444-5555-6666-77
ifconfig eth1 192.168.1.1
route add default 192.168.1.254
module ieee1394
lm-sensors 2.10.3
N'a pas l'air de fonctionner correctement (sensors-detect semble détecter
le matériel, mais sensors ne donne rien).
Fonctionne correctement
Dernière mise à jour le mercredi 2 janvier 2008